Drift
12 of 12 entries
| ID | Risk | Title | CVSS | CWE |
|---|---|---|---|---|
DRIFT-001 |
INFO |
Wireless Reconnection Successful
The wireless interface successfully disconnected from and reconnected to the target SSID within the expected time window...
|
— | — |
DRIFT-002 |
INFO |
Wireless Reconnection Failed or Timed Out
The reconnect command was issued but the interface did not confirm association with the target SSID within the 20-second...
|
— | — |
DRIFT-003 |
INFO |
SSID Mismatch After Reconnect
After issuing the reconnect command for the target SSID, the interface associated with a different SSID. This may indica...
|
— | — |
DRIFT-004 |
INFO |
Wireless Interface Not Found
The specified or auto-detected wireless interface could not be found on the system. The tool is unable to perform any di...
|
— | — |
DRIFT-005 |
INFO |
Target Network Not Available
The interface is not currently associated with the expected SSID at the start of a cycle. The target network may be temp...
|
— | — |
DRIFT-006 |
INFO |
Cycle Completed Successfully
A full disconnect/reconnect cycle completed without error. Both the disconnect and reconnect commands succeeded, and the...
|
— | — |
DRIFT-007 |
INFO |
Maximum Cycle Count Reached
The configured maximum number of disconnect/reconnect cycles has been reached. The tool has exited normally.
|
— | — |
DRIFT-008 |
INFO |
Disconnect Command Returned Non-Zero Exit Code
The OS wireless disconnect command (iw, wpa_cli, nmcli, or airport) returned a non-zero exit code. The interface may not...
|
— | — |
DRIFT-009 |
INFO |
Reconnect Command Returned Non-Zero Exit Code
The OS wireless reconnect command returned a non-zero exit code. The network may not have been joined. This may indicate...
|
— | — |
DRIFT-010 |
INFO |
Dry-Run Cycle Completed (Simulated)
A cycle completed in dry-run mode. No actual wireless commands were issued. This confirms the timing logic and argument ...
|
— | — |
DRIFT-011 |
INFO |
Privilege Escalation Required for Wireless Commands
Wireless management commands (iw, nmcli, airport) require elevated privileges. The tool invokes these via sudo. If passw...
|
— | — |
DRIFT-012 |
INFO |
Interface Auto-Detection Fallback Used
The wireless interface was not explicitly specified. The tool fell back to parsing /proc/net/wireless or airport output ...
|
— | — |
Detailed View
INFO DRIFT-001 — Wireless Reconnection Successful
Description: The wireless interface successfully disconnected from and reconnected to the target SSID within the expected time window. The SSID association was confirmed by polling the interface state.
INFO DRIFT-002 — Wireless Reconnection Failed or Timed Out
Description: The reconnect command was issued but the interface did not confirm association with the target SSID within the 20-second polling window. This may indicate a weak signal, aggressive rate-limiting of (re)association requests by the AP, or a WPA Enterprise authentication delay.
INFO DRIFT-003 — SSID Mismatch After Reconnect
Description: After issuing the reconnect command for the target SSID, the interface associated with a different SSID. This may indicate the presence of a rogue access point with a stronger signal, or unintended roaming to an adjacent network.
INFO DRIFT-004 — Wireless Interface Not Found
Description: The specified or auto-detected wireless interface could not be found on the system. The tool is unable to perform any disconnect/reconnect operations.
INFO DRIFT-005 — Target Network Not Available
Description: The interface is not currently associated with the expected SSID at the start of a cycle. The target network may be temporarily unavailable, out of range, or the interface has roamed to a different network.
INFO DRIFT-006 — Cycle Completed Successfully
Description: A full disconnect/reconnect cycle completed without error. Both the disconnect and reconnect commands succeeded, and the association with the target SSID was confirmed.
INFO DRIFT-007 — Maximum Cycle Count Reached
Description: The configured maximum number of disconnect/reconnect cycles has been reached. The tool has exited normally.
INFO DRIFT-008 — Disconnect Command Returned Non-Zero Exit Code
Description: The OS wireless disconnect command (iw, wpa_cli, nmcli, or airport) returned a non-zero exit code. The interface may not have cleanly disassociated before the reconnect attempt.
INFO DRIFT-009 — Reconnect Command Returned Non-Zero Exit Code
Description: The OS wireless reconnect command returned a non-zero exit code. The network may not have been joined. This may indicate the SSID is not in the system's known network profiles, or that the wireless daemon rejected the connection attempt.
INFO DRIFT-010 — Dry-Run Cycle Completed (Simulated)
Description: A cycle completed in dry-run mode. No actual wireless commands were issued. This confirms the timing logic and argument parsing are functioning correctly.
INFO DRIFT-011 — Privilege Escalation Required for Wireless Commands
Description: Wireless management commands (iw, nmcli, airport) require elevated privileges. The tool invokes these via sudo. If passwordless sudo is not configured, interactive prompts may interrupt automated testing.
INFO DRIFT-012 — Interface Auto-Detection Fallback Used
Description: The wireless interface was not explicitly specified. The tool fell back to parsing /proc/net/wireless or airport output to determine the active interface. The selected interface may not be the intended test adapter.